John East Marcus Retro 01 Preamp (Plate'siz)

John East Marcus Retro 01 Preamp (Plate'siz)

Ürün no 69909
Barkod MR01-XCC-DX
Marka John East
Fiyat 1.412,55 TL Taksit seçenekleri
Havale fiyatı 1.341,92 TL Bu niye daha ucuz?
Stokta yok
  • İstek listene ekle
  • Fiyatı düşünce haber ver
  • Ürün Rozeti paylaş
    HTML
    BBCode
  • Yorumlar
  • Ürün detayları
  • Hata bildir
GaRaJ Dükkan'da satılan tüm ürünler distribütör firmaların garantisi ile, sıfır, orjinal ambalajında satılmaktadır. Siparişleriniz ile birlikte gönderilen faturalarınızı lütfen saklayın.
Marcus Retro 01 Preamp Plate'siz

(Fotoğrafta görünen siyah Plate olmadan gönderilecektir)



The MARCUS RETRO 01 was brought about due to requests from players owning the Marcus Miller basses. Most of the circuit is the same as the Retro except that the bass and treble turnover frequencies, or ‘corner frequencies’, are designed to match that of the Marcus pre. 



It's high quality circuit uses three stacked knobs plus a single knob. It includes an active blend circuit plus 3 band equaliser with bass, variable frequency mid, treble and bright function. A passive tone circuit is also included which operates in both active and passive modes. 



A very gentle built in contour gives immediate colour without detracting from the basic sound of any bass. The active blend circuit prevents the loss associated with many passive basses where, when both pickups are up full, the signal from one pickup feeds into the other and vice versa. 



However, a switch is included to allow a passive equal mix of both pickups. A second switch - basic "get-you-out-of-trouble" passive mode is included in case the battery dies in crucial circumstances, but this mode allows lots of useful settings too. 



EASY TO FIT, NO ROUTING OR MODS TO MOST Marcus Miller J DELUXE STYLE BASSES. 



Standard Black Scratch Plate with Chrome Knobs and Toggles. 



Marcus Retro 01 Technical



VOLUME & BLEND (Knob stack nearest the neck pickup) 



VOLUME 

The upper knob is the Volume which has two sections under the same knob. A high impedance section is used for the passive path and low impedance for the active circuitry. When used active, this knob has active circuitry after it so that the feed to your amplifier is a low impedance drive. 



BLEND & PICKUPS SWITCH

The lower outer knob is the Blend balance for the pickups. Turn it fully clockwise for the neck pickup alone and fully anti-clockwise for the bridge pickup. The midway position, which has an indent, gives an equal mix of both pickups. The balance between the pickups is continuously variable with progressive level compensation towards the single pickup settings. 



Important:- The Pickups switch (by the blend) must be set pointing towards the jack for the Blend to function. In passive mode, the bridge pickup or both pickups can be used. 



BASS & TREBLE (The middle knob stack) 



TREBLE (+12dB @ 1k5Hz, -12dB @ 1kHz) 

The upper knob is the Treble control with boost and cut. The central 'flat' position is indented. The cut settings work on lower frequencies compared to boost to give a deeper sound when the top is rolled off. 



BRIGHT (+8dB @ 7kHz) 



Pull the Treble knob for the Bright setting. 



BASS (+15dB @ 40Hz) 

The lower outer knob is the boost only Bass control. The frequency band of boost gets progressively lower as the boost is increased. An indent midway is included to aid the setting of this control. 



MID LEVEL & FREQUENCY (The knob stack nearest the jack) 



BOOST/CUT (+/- 12dB) 

The upper knob controls the amount of Mid boost or cut at frequencies according to the setting of the Frequency knob. The midway indent is the 'flat' position. 



FREQUENCY (150Hz - 3kHz) 

The lower outer knob is continuously variable and sets the Mid frequencies for boost or cut. 



PASSIVE TONE (Single knob near the jack) 



The passive tone pot consists of two sections, one for each pickup. Two sections are necessary since the pickup signals are kept separate and fed to their own individual input amplifiers prior to the electronic blend circuitry. 



To retain the characteristics of a true passive tone, its circuitry is connected directly to the pickups at all times, and therefore it functions in both active and passive modes. The roll-off frequency is set to give a deep mellow sound. 



ACTIVE PASSIVE SWITCH (By the jack) 



Towards the jack for active, the opposite for passive. 



POWER 

The PP3 battery is switched on automatically when a mono jack is plugged into the socket.
Ürünle ilgili gördüğün hatayı bize bildirirsen düzeltmek için elimizden geleni yapacağız, söz.

Hata


Detay


Bunlar da var